CRITICAL REVIEW ON DESIGN OF ROLLING PROCESS
DOI:
https://doi.org/10.2022/jmet.v9i2.1897Abstract
Rolling is one of the important forming processes used in steel industry. During rolling process because of overdraft and poor die design, cracks and breakage of rolls takes place, leading to shutdown of rolling mill. There is a need for proper deign of rolling dies based on work piece material. In the present paper design methodologies followed by various researchers are presented. Review on works related to Finite Element Analysis (FEA) methods and material selection is carried out and presented.
Downloads
References
A Bauer, T Mehner, C Binotsch, M Sieber, B Awiszus and T Lampke, “Experimental and numerical investigation on cold flat rolling processes of DC04 sheets with special focus on residual stresses’’, Materials Science and Engineering, Vol. 118 ,2016, 012019 , pp.1-9.
Andre Lim, Sylvie Castagne, Chow Cher Wong, “Effect of Deep Cold Rolling on Residual Stress Distributions Between the Treated and Untreated Regions on Ti–6Al–4V Alloy”, Journal of Manufacturing Science and Engineering, Vol. 138(11),2016, Paper No: MANU-15-1371.
Kaixiang Peng, “Calculation and Analysis of Temperature Distribution in Hot Rolling Strip”, TELKOMNIKA Indonesian Journal of Electrical Engineering, Vol. 11, No. 7, 2013,pp. 3945 – 3956.
Tetsuo shinohara and kazunariyoshida, “Deformation Analysis of Surface Crack in Rolling and Wire Drawing”, JSME International Journal series A ,Vol. 48 No. 4 ,2005,pp. 335-340.
A. Alsamhan,P. Hartely, I. Pillinger, “The computer simulation of cold-roll-forming using FE methods and applied real time re-meshing techniques”, Journal of Materials Processing Technology, Vol. 142 ,2003,pp.102–111.
Chunlei Xie Xianghuai Dong, Shangjian Li, Shuhuai Huang, “Rigid–visco plastic dynamic explicit FEA of the ring rolling process”, International Journal of Machine Tools &Manufacture, Vol. 40,2000,pp. 81–93.
M.R. Forouzan,M. Salimi, M.S. Gadala, “Three-dimensional FE analysis of ring rolling by employing thermal spokes method”, International Journal of Mechanical Sciences, Vol. 45, 2003,pp.1975–1998.
Santosh Kumar and Prof.Bharat S Kodli, “A Study On Thermo-Mechanical Analysis Of Hot Rolling &Estimation Of Residual Stresses By Using FEM”, IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE), Vol.9, Issue 3, 2013,pp.26-34.
NilamK.Wankhade and Dhananjay. R. Ikhar, “Design and Analysis Of Axial Crossing Of Work Rolls In Rolling Mill Work Roll Assembly: A Review”, International Journal of Mechanical Engineering and Technology (IJMET), Vol.7, Issue 2, 2016,pp.191–195.
Shaibu V B, “Numerical Analysis of Work Roll Cooling In Hot Rolling Process” ,Mater of Technology thesis, Department of Mechanical Engineering National Institute of Technology Rourkela,2012.
Z.W. Wang, S.Q. Zeng, X.H. Yang, C. Cheng. “The key technology and realization of virtual ring rolling” Journal of Materials Processing Technology,Vo.182, 2007,pp. 374–381.
NataliyaLyubenova and Dirk Baehre.“Finite Element Modeling and Investigation of the Process Parameters in Deep Rolling of AISI 4140 Steel”, Journal of Materials Science and Engineering B Vol.5, Issue. (7-8), 2015, pp.277-287.
Wen Kang,Yixi Zhao, Wangwei Yu, Shanshuai Wang, Yuefeng Ma, Peijie Yan, “Numerical simulation and parameters analysis for roll forming of martensitic steel MS980”, 11th International Conference on Technology of Plasticity, 2014,pp. 251-256.
Lanyun Li,He Yang, LianggangGuo, Zhichao Sun, “A control method of guide rolls in 3D-FE simulation of ring rolling”, Journal of materials processing technology,Vol.205, 2008,pp. 99–110.
He Yang,LianggangGuo, Mei Zhan, Zhichao Sun, “Research on the influence of material properties on cold ring rolling processes by 3D-FE numerical simulation”, Journal of Materials Processing Technology, Vol.177, 2006, pp.634–638.
A.M. Abrao,B. Denkena, J. Köhler, B. Breidenstein and T. Mörke, “The Influence Of Deep Rolling On The Surface Integrity Of AISI 1060 High Carbon Steel” ,The International Scientific Committee of the “2nd Conference on Surface Integrity Procedia CIRP 13, 2014, pp.31 – 36.
R S Nalawade,V R Marje, G Balachandran and V Balasubramanian, “Effect of Pass Schedule and Groove Design on The Metal Deformation Of 38mnvs6 In The Initial Passes Of Hot Rolling”, Indian Academy of Sciences, Vol. 41, No. 1, 2016,pp. 111–124.
S. G. Xu, K. J. Weinmann, D. Y. Yang, J. C. Lian, “Simulation of The Hot Ring Rolling Process By Using A Thermo-Coupled Three-Dimensional Rigid-ViscoplasticFinite Element Method” , Journal of Manufacturing Science and Engineering, Vol. 119, 1997, pp.542-549.
Kenji Tsubouchi, Masayoshi Akiyama, Eiji Yamamoto, Toshiro Mase, “Development of a New Tool Material to Ensure High Performance in Hot Steel Rolling”, ,Journal on Tribology, Vol. 121, 1999, pp.739-745.
G. Plicht, H. Schillak, H. Hofinghoff and T. Demski, C.D. Walzholz, “Cold Rolling of Metal Strip Using Technical Gases”, Air Products and Chemicals, Inc., 2010
Saral Dutta, “Hot Rolling Practice – An Attempted Recollection” B. Tech. (Hons.), I.I.T. Executive Director, ISP & RMD, SAIL
Vladimir Panjkovic, Ronald Gloss, John Steward, Stephen Dilks, Robert Steward, Gregory Fraser,“Causes of Chatter in A Hot Strip Mill: Observations, Qualitative Analyses and Mathematical Modeling”, Journal of Materials Processing Technology, Vol. 212, 2012, pp.954– 961.
John M. Sech, David I. Weinstein, E.Michael, “Evaluation of rolling oils used in the cold rolling process for sheet steel by thermogravimetry” Journal of Petroleum Science and Engineering ,1990. AMM.331.591.
Kunal Ganguly, “Improvement Process for Rolling Mill through the Dmaic Six Sigma Approach”, International Journal for Quality research Short Scientific Paper (1.03),Vol 6, No. 3, 2012,pp. 221-231
V.Deepika Satya Bhanu and Dr P Mallesham, “Sheet Metal Rolling Using Two Roller Powered Machine”, International Journal in IT and Engineering, Vol.04 Issue-01, 2016,pp.1-12.
Dr.-Ing. J. Mackel, “Maintenance and quality related condition monitoring in rolling mills”, Presented at the 2000 AISE Annual Convention, pp.1-14.
Zhao yang Gao, LinfaPeng, Peiyun Yi, Xinmin Lai,“An Experimental Investigation on the Fabrication of Micro/ Meso Surface Featuresby Metallic Roll-to-Plate Imprinting Process”, Journal of Micro- and Nano-Manufacturing by ASME, Vol. 1, 2013, pp.1-10.
Xiaoxin Ye, Zion T.H. Tse, Guoyi Tang, Xiaohui Lia, Guolin Song, “Effect Of Electro Pulsing Treatment on Microstructure And Mechanical Properties of Cold-Rolled Pure Titanium Strips”, Journal of Materials Processing Technology, Vol.222, 2015,pp. 27–32.
Chow Cher Wong, Andry Hartawana, Wee Kin Teo, “Deep Cold Rolling of Features on Aero-Engine Components”, 2nd CIRP Conference on Surface Integrity (CSI) Procedia CIRP Vol.13, 2014,pp.350 – 354.
Hongchun Li , A study on wear and surface roughness of work roll in cold rolling, Dotor of Philosophy thesis, University of Wollongong, 2008.
Downloads
Published
Issue
Section
License
JMET Copyright Principles
JMET seeks to retain copyright of the articles it publishes, without the authors giving up their right to use their own material.
Originality
The manuscript is neither been published before, nor is it under consideration for publication in any other journals. It contains no matter that is scandalous, obscene, libelous or otherwise contrary to law.
Terms of Acceptance
When the article is accepted for publication, the authors shall hereby agree to transfer to the Journal of Mechanical Engineering and Technology, all rights, including those pertaining to electronic forms and transmissions, under existing copyright laws, except for the following, which the author(s) specifically retain(s):
All proprietary right other than copyright, such as patent rights.
- The right to make further copies of all or part of the published article for my/our use in classroom teaching.
- The right to reuse all or part of this material in a compilation of my/our own works or in a textbook of which I/we am/are the author(s).
- The right to make copies of the published work for internal distribution within the institution that employs me/us.
The authors agree that copies made under these circumstances will continue to carry the copyright notice that appeared in the original published work. The authors agree to inform any co-authors, if any, of the above terms. The authors certify that they have obtained written permission for the use of text, tables, and/or illustrations from any copyrighted source(s), and they agree to supply such written permission(s) to Journal of Mechanical Engineering and Technology upon request.
